Cuanto Cuesta Recessed Lighting Installation en Marysville, CA? (2026)

Costo Promedio

$1,959–$4,135

Materiales

$1,055–$2,492

Mano de Obra (Yuba-Sutter)

$452–$689

Las tarifas de mano de obra en Yuba-Sutter son -10% comparadas con la linea base de Sacramento Metro.

Recessed lighting (can lights or downlights) provides clean, modern illumination without protruding fixtures. We install IC-rated (insulation contact) LED recessed housings in new-construction and remodel configurations. The project includes cutting ceiling openings, running NM-B cable from a switched circuit, installing the housings and LED trim modules, and connecting a compatible LED dimmer switch. We plan layouts based on room size, ceiling height, and desired light levels using the standard spacing formula (spacing = ceiling height / 2). LED modules produce warm or cool white light, use 75% less energy than incandescent cans, and last 50,000+ hours.

Marysville se encuentra en el condado de Yuba (Yuba-Sutter). Historic levee-protected city with older Victorian and craftsman homes. El proveedor local de energia es PG&E.

Calculadora de Costos

Ajuste los detalles para obtener su estimado

Ciudad

Lights

Materiales Incluidos

IC-Rated LED Recessed Housing (6", new-work or remodel)36 each

$432–$1,080

LED Trim Module (12W, 3000K-4000K, dimmable)36 each

$288–$792

14/2 NM-B Cable (per 50 ft)12 roll

$300–$540

LED-Compatible Dimmer Switch1 each

$20–$50

Wire Connectors, Boxes & Mounting Hardware1 set

$15–$30

Mano de Obra(Yuba-Sutter -10%)

Licensed Electrician4.5h @ $77–$117/hr

$344–$527

Electrician's Apprentice3h @ $36–$54/hr

$108–$162

Margen del Contratista30%

0%Promedio 30%100%

Materiales

$1,055–$2,492

Mano de Obra

$452–$689

Margen

$452–$954

Costo Total Estimado

$1,959 – $4,135

$327–$689 por unidad

Quiere Su Precio Exacto?

Este es un estimado. Obtenga una cotizacion precisa y sin compromiso.

Llamar (916) 476-7689 Cotizacion Gratis

Codigo de Construccion de California

California Title 24 requires high-efficacy luminaires (LED qualifies) in all new residential lighting installations. IC-rated housings are required where insulation may contact the fixture. Dimmer switches must be compatible with LED modules to prevent flicker.

Cronograma del Proyecto

Layout Planning

20-30 min

Determine light placement using the ceiling height / 2 spacing rule. Mark ceiling locations, verify no obstructions (joists, ducts, wiring) above the planned positions using a stud finder.

Ceiling Cuts & Wiring

1-3 hrs

Cut circular openings in the ceiling with a hole saw. Run NM-B cable from the switch location through the attic or ceiling cavity, daisy-chaining from light to light. Install the switch box.

Housing & Trim Installation

1-2 hrs

Insert remodel housings into the ceiling cutouts and engage the retention clips. Connect wiring to each housing. Snap in the LED trim modules. Install the dimmer switch at the wall box.

Testing & Adjustment

15-20 min

Restore power and test all lights on the dimmer at full and low settings. Verify even illumination, confirm no flickering, and adjust trim positions if needed.

Desglose de Materiales

Material	Cantidad	Unidad	Costo Unitario	Total
IC-Rated LED Recessed Housing (6", new-work or remodel)	36	each	$12–$30	$432–$1,080
LED Trim Module (12W, 3000K-4000K, dimmable)	36	each	$8–$22	$288–$792
14/2 NM-B Cable (per 50 ft)	12	roll	$25–$45	$300–$540
LED-Compatible Dimmer Switch	1	each	$20–$50	$20–$50
Wire Connectors, Boxes & Mounting Hardware	1	set	$15–$30	$15–$30

Recessed Lighting Installation en Marysville — Preguntas Frecuentes

How much does recessed lighting cost per light?+

In NorCal, recessed lighting costs $150-$250 per light installed when doing 4-6 lights at once. The per-light cost decreases with more lights since much of the labor is in routing the wire. A typical 6-light kitchen install runs $900-$1,500.

How many recessed lights do I need?+

Use the ceiling height / 2 spacing rule. For a standard 8-foot ceiling, space lights 4 feet apart. A 12x14 kitchen typically needs 6 lights in two rows of three. We adjust based on room layout and your lighting preferences.

Can I add recessed lights without attic access?+

Yes. Remodel (old-work) housings clip directly into the ceiling cutout from below, requiring no attic access. Wiring is fished through the ceiling cavity. This is how we install recessed lights in most finished NorCal homes.

Do I need IC-rated housings?+

Yes. IC-rated (Insulation Contact) housings are required anywhere the housing may contact attic insulation. Since virtually all NorCal attics have insulation, we use IC-rated housings on every installation.