Cuanto Cuesta Furnace Repair en Auburn, CA? (2026)

Costo Promedio

$216–$408

Materiales

$40–$125

Mano de Obra (Placer County)

$126–$189

Las tarifas de mano de obra en Placer County son +5% comparadas con la linea base de Sacramento Metro.

Furnace repair covers diagnosing and resolving issues such as ignition failures, faulty flame sensors, blower motor problems, cracked heat exchangers, thermocouple replacement, control board failures, and gas valve issues. A skilled technician will perform a complete safety inspection alongside the repair to ensure your furnace operates safely and efficiently. This estimate covers the most common furnace repairs with Sacramento-area 2025-2026 pricing.

Auburn se encuentra en el condado de Placer (Placer County). Historic Gold Rush town with mix of Victorian and modern homes. El proveedor local de energia es PG&E.

Calculadora de Costos

Ajuste los detalles para obtener su estimado

Ciudad

Repair visits

Materiales Incluidos

Hot surface ignitor1 each

$20–$60

Flame sensor rod1 each

$8–$25

Blower motor (1/2 HP)1 each

$120–$350

Run capacitor1 each

$12–$40

Furnace control board1 each

$100–$350

Mano de Obra(Placer County +5%)

HVAC service technician1.5h @ $84–$126/hr

$126–$189

Margen del Contratista30%

0%Promedio 30%100%

Materiales

$40–$125

Mano de Obra

$126–$189

Margen

$50–$94

Costo Total Estimado

$216 – $408

Quiere Su Precio Exacto?

Este es un estimado. Obtenga una cotizacion precisa y sin compromiso.

Llamar (916) 476-7689 Cotizacion Gratis

Codigo de Construccion de California

California requires carbon monoxide detectors in all homes with gas appliances. After any furnace repair involving the gas valve, burner, or heat exchanger, a CO safety check is mandatory.

Cronograma del Proyecto

Diagnostic inspection

30-45 minutes

Inspect the furnace visually, check error codes on the control board, test electrical components (ignitor, flame sensor, capacitor, pressure switches), and verify gas pressure.

Component repair or replacement

30 minutes - 2 hours

Replace the faulty component, clean the flame sensor, replace the ignitor, swap the capacitor, or install a new blower motor as determined by the diagnostic.

Safety testing & verification

15-30 minutes

Perform a combustion analysis, check for carbon monoxide leaks, verify temperature rise is within manufacturer specifications, and test all safety controls before returning the furnace to service.

Desglose de Materiales

Material	Cantidad	Unidad	Costo Unitario	Total
Hot surface ignitor	1	each	$20–$60	$20–$60
Flame sensor rod	1	each	$8–$25	$8–$25
Blower motor (1/2 HP)	1	each	$120–$350	$120–$350
Run capacitor	1	each	$12–$40	$12–$40
Furnace control board	1	each	$100–$350	$100–$350

Furnace Repair en Auburn — Preguntas Frecuentes

My furnace clicks but won't light — what's wrong?+

The most common causes are a failed hot surface ignitor ($80-$200 repair), a dirty flame sensor ($80-$150 cleaning/replacement), or a faulty gas valve ($250-$600). A technician can diagnose the exact cause in 30-45 minutes.

When should I repair vs. replace my furnace?+

Consider replacement if your furnace is over 15-20 years old, needs a heat exchanger replacement ($1,500+), or has needed multiple repairs totaling more than 50% of a new unit's cost. Otherwise, repair is usually more cost-effective.

Is a cracked heat exchanger dangerous?+

Yes. A cracked heat exchanger can leak carbon monoxide into your home. If a crack is confirmed, the furnace should be shut down immediately and either the heat exchanger replaced (if under warranty) or the entire furnace replaced.

How much does a typical furnace repair cost?+

Most furnace repairs in Sacramento cost $150-$500, including the diagnostic fee. Common repairs like ignitor or flame sensor replacement are at the lower end, while blower motor or control board replacements are higher.